guns for sale

How to Feed Your Firearm During the Ammo Shortage

Regardless of whether the ammunition is made into steel surplus or match-grade ammo, desperate times call for desperate measures if it is difficult to find food.How to Feed Your Firearm During the Ammo Shortage

I am aware that since 2008 there have been at least three major commercial ammunition shortages, each as result of some kind of political action or reaction. I assume everyone believes that the current drought is the worst. Many things happen if supply and demand economics impact this industry.

First of all, items begin to sell fast because experience tells people to buckle in for the journey. Next, prices will start to rise as stocks remain low, even if producers overdrive.

guns for sale near me
How to Feed Your Firearm During the Ammo Shortage

Tight managing components and inevitably disappear as well. When the dust settles down, prospective ammunition shoppers have three key choices: (1) Premium loads, which are exorbitantly more expensive than usual, (2) Modest rates but low-cost ammunitions, or (3) curtailing for a complete shoot. No such choice is fine, but it has its advantages to choose door number two.

I frequently inquire about the best ammunition type for the newly constructed weapons of my customers. The issue moves from “What is the best use load” during irregular times such as these. “To “I can find ammunition where? “And finally, ‘I shall buy this load of budget until it also disappears? “The good news is that reasonably priced ammunition is available at least in waves in most traditional rifle calibers. The bad news is that low-grade ammunition is also preceded by such cautions. How to Feed Your Firearm During the Ammo Shortage.

Steel-Cased Stuff


Steel casing ammunition is renewed when conventional brass casing is scarce. I still advise you to be careful when you have leftover ammunition from former Soviet representatives or allies (normally 7.62×39 mm, 7.62×54 mm R and 5.45×39 mm). In addition to visual details like rusted cases, you can’t know how this content has been stored in decades—wet, dry, intense cold or heat, and more.

It is also almost likely that it is corrosively coated and thus needs the bore of your gun to be washed immediately after use. However, it is generally OK to use new steel-case ammunition production (usually from Russia), given that you remember some key points.

As steel doesn’t behave as brass when pressurized in the chamber of a firearm, repeated-rifle components appear to be more difficult to use. Extractors get the hardest hit, frequently breaking away much faster than they would if only standard bullets were used. For this purpose, standard ammunition casing steel screwdrivers are wise to maintain an extractor. Another issue is the use of projectiles, not copper, in the conventional context of the stuff coming out of Russia. Their jackets are instead a thin cotton lining, often covered by a jacket of steel. This coating is sufficiently thin to reveal everything beneath it as the bullet moves through a strongly shaken bore.

The question is how much this impacts on barrel wear. On both sides of the argument, I saw many anecdotal reports and some comprehensive studies which show the use of these bullets. My 5,56 NATO, 6,5 Grendel, 7,62×39 mm and .308 Win are firing various steel-cased loads personally. Rifles without complications or rapid wear signals. But when using copper-coated steel-jacket projectiles I’m careful to keep my round figures reasonably low.

If your steel case has a heavy lacquer layer which makes it shiny, it is important, once your rifle has cleaned its boore, to scrub the residue left behind on your chamber walls. It can otherwise build up and cause functional problems. You may also run into hard primers, for example in the 7,62×39 mm non-AK/SKS rifles, where heavier hammer springs or increased fire pins are needed.

Extra-made rifle ammunition, made of steel, is typically unreliable and appears to make a lovely fireball shorter than 16 inches in any barrel. But if anything you can find and can maintain a moderate level of training or raise your reservation supply—or both—then it remains a viable choice.

Brass-Cased Target Fodder


This category includes genuine surplus military munitions as well as loads which imitate them, for example tens of 55 grains.223 Rem. Or 5.56 NATO M193 Ball load clones with Army Basic Training trained like me. For several new and old rifle calibers, full-metal jacket loads are available. They are less expensive than they do in hunting or defense performance.

Naturally, the price is subjective. Usually you’ll find the equivalent 145-kernel M80 ball in 7.62 NATO or 308 Win. It runs twice or more, for 40 to 50 cents per round, but when it is posted. Again, precision will typically not be the strong suit of this ammunition. In addition, the same safeguards apply to bullets from overseas stocks as to steel-cased ammunition — including corrosive first concerns. Finally, Berdan will be primed for most of the content from European surplus inventories, so it will not be practical to reload the cases.

Newly developed FMJ brass-cased loads seem to fit well in most weapons, and can keep your practice up without sacrificing the college fund for your boy. Secondly, given the modern condition of many ‘higher education institutes,’ it might not be a very poor deal to exchange the money for ammunition.

I have here omitted ammunition that is treated or made, because it is broad subjects. If you want to fire “Remain” ammunition that you personally haven’t handled, be sure that the supply comes from a trained and certified source to load and sell ammo. The availability of fairly expensive ammunition will soon once more be a fact in a perfect world. I do not intend to expand on this hope but rather to proceed with a changed training scheme which will secure my regular motorcycle with moderate quantities of usable target loads. I’m probably also going to order more spare extractors.

Leave a Comment

Your email address will not be published. Required fields are marked *